一天一个 Linux 命令（30）：hdparm 命令

本文为joshua317原创文章,转载请注明：转载自joshua317博客 一天一个 Linux 命令（30）：hdparm 命令 - joshua317的博客

Linux下的hdparm（英文全称：hard disk parameters）命令，主要用来查看硬盘的相关信息或对硬盘进行测速、优化、修改硬盘相关参数设定。它提供了一个命令行的接口用于读取和设置IDE或SCSI硬盘参数。

若没有安装hdparm ，可以通过sudo yum install hdparm 来安装。

hdparm  [options] ...[device]...
hdparm  [参数]...[设备]...

Options:
 -a   Get/set fs readahead
 -A   Get/set the drive look-ahead flag (0/1)
 -b   Get/set bus state (0 == off, 1 == on, 2 == tristate)
 -B   Set Advanced Power Management setting (1-255)
 -c   Get/set IDE 32-bit IO setting
 -C   Check drive power mode status
 -d   Get/set using_dma flag
 -D   Enable/disable drive defect management
 -E   Set cd/dvd drive speed
 -f   Flush buffer cache for device on exit
 -F   Flush drive write cache
 -g   Display drive geometry
 -h   Display terse usage information
 -H   Read temperature from drive (Hitachi only)
 -i   Display drive identification
 -I   Detailed/current information directly from drive
 -J   Get/set Western DIgital "Idle3" timeout for a WDC "Green" drive (DANGEROUS)
 -k   Get/set keep_settings_over_reset flag (0/1)
 -K   Set drive keep_features_over_reset flag (0/1)
 -L   Set drive doorlock (0/1) (removable harddisks only)
 -m   Get/set multiple sector count
 -M   Get/set acoustic management (0-254, 128: quiet, 254: fast)
 -n   Get/set ignore-write-errors flag (0/1)
 -N   Get/set max visible number of sectors (HPA) (VERY DANGEROUS)
 -p   Set PIO mode on IDE interface chipset (0,1,2,3,4,...)
 -P   Set drive prefetch count
 -q   Change next setting quietly
 -Q   Get/set DMA queue_depth (if supported)
 -r   Get/set device readonly flag (DANGEROUS to set)
 -R   Get/set device write-read-verify flag
 -s   Set power-up in standby flag (0/1) (DANGEROUS)
 -S   Set standby (spindown) timeout
 -t   Perform device read timings
 -T   Perform cache read timings
 -u   Get/set unmaskirq flag (0/1)
 -U   Obsolete
 -v   Use defaults; same as -acdgkmur for IDE drives
 -V   Display program version and exit immediately
 -w   Perform device reset (DANGEROUS)
 -W   Get/set drive write-caching flag (0/1)
 -x   Obsolete
 -X   Set IDE xfer mode (DANGEROUS)
 -y   Put drive in standby mode
 -Y   Put drive to sleep
 -z   Re-read partition table
 -Z   Disable Seagate auto-powersaving mode
 --dco-freeze      Freeze/lock current device configuration until next power cycle
 --dco-identify    Read/dump device configuration identify data
 --dco-restore     Reset device configuration back to factory defaults
 --direct          Use O_DIRECT to bypass page cache for timings
 --drq-hsm-error   Crash system with a "stuck DRQ" error (VERY DANGEROUS)
 --fallocate       Create a file without writing data to disk
 --fibmap          Show device extents (and fragmentation) for a file
 --fwdownload            Download firmware file to drive (EXTREMELY DANGEROUS)
 --fwdownload-mode3      Download firmware using min-size segments (EXTREMELY DANGEROUS)
 --fwdownload-mode3-max  Download firmware using max-size segments (EXTREMELY DANGEROUS)
 --fwdownload-mode7      Download firmware using a single segment (EXTREMELY DANGEROUS)
 --idle-immediate  Idle drive immediately
 --idle-unload     Idle immediately and unload heads
 --Istdin          Read identify data from stdin as ASCII hex
 --Istdout         Write identify data to stdout as ASCII hex
 --make-bad-sector Deliberately corrupt a sector directly on the media (VERY DANGEROUS)
 --offset          use with -t, to begin timings at given offset (in GiB) from start of drive
 --prefer-ata12    Use 12-byte (instead of 16-byte) SAT commands when possible
 --read-sector     Read and dump (in hex) a sector directly from the media
 --repair-sector   Alias for the --write-sector option (VERY DANGEROUS)
 --security-help   Display help for ATA security commands
 --trim-sector-ranges        Tell SSD firmware to discard unneeded data sectors: lba:count ..
 --trim-sector-ranges-stdin  Same as above, but reads lba:count pairs from stdin
 --verbose         Display extra diagnostics from some commands
 --write-sector    Repair/overwrite a (possibly bad) sector directly on the media (VERY DANGEROUS)

-a<快取分区>：设定读取文件时，预先存入块区的分区数，若不加上<快取分区>选项，则显示目前的设定；
-A<0或1>：启动或关闭读取文件时的快取功能；
-c：设定IDE32位I/O模式；
-C：检测IDE硬盘的电源管理模式；
-d<0或1>：设定磁盘的DMA模式；
-f：将内存缓冲区的数据写入硬盘，并清除缓冲区；
-g：显示硬盘的磁轨，磁头，磁区等参数；
-h：显示帮助；
-i：显示硬盘的硬件规格信息，这些信息是在开机时由硬盘本身所提供；
-I：直接读取硬盘所提供的硬件规格信息；
-k<0或1>：重设硬盘时，保留-dmu参数的设定；
-K<0或1>：重设硬盘时，保留-APSWXZ参数的设定；
-m<磁区数>：设定硬盘多重分区存取的分区数；
-n<0或1>：忽略硬盘写入时所发生的错误；
-p：设定硬盘的PIO模式；
-P<磁区数>：设定硬盘内部快取的分区数；
-q:在执行后续的参数时，不在屏幕上显示任何信息；
-r<0或1>:设定硬盘的读写模式；
-S<时间>:设定硬盘进入省电模式前的等待时间；
-t;评估硬盘的读取效率；
-T：评估硬盘缓存的读取速度；
-u<0或1>：在硬盘存取时，允许其他中断要求同时执行；
-v：显示硬盘的相关设定；
-w<0或1>：设定硬盘的写入快取；
-X<传输模式>：设定硬盘的传输模式；
-y：使IDE硬盘进入省电模式；
-Y：使IDE硬盘进入睡眠模式；
-Z：关闭某些Seagate硬盘的自动省电功能。

# hdparm /dev/vda

/dev/vda:
 HDIO_DRIVE_CMD(identify) failed: Inappropriate ioctl for device
 readonly      =  0 (off)
 readahead     = 8192 (on)
 geometry      = 104025/16/63, sectors = 104857600, start = 0

# hdparm -g /dev/vda

/dev/vda:
 geometry      = 104025/16/63, sectors = 104857600, start = 0
 
 #其中：
geometry = 104025［柱面数］/16［磁头数］/63［扇区数］, sectors = 104857600［总扇区数］, start = 0［起始扇区数］

# hdparm -t /dev/vda

/dev/vda:
 Timing buffered disk reads: 290 MB in  3.15 seconds =  92.08 MB/sec

# hdparm -T /dev/vda

/dev/vda:
 Timing cached reads:   20508 MB in  2.00 seconds = 10267.18 MB/sec

# hdparm -C /dev/vda

/dev/vda:
 drive state is:  unknown

#查看
# hdparm -m /dev/vda

#设置
# hdparm -m 8 /dev/vda

#hdparm -I /dev/vda

# hdparm -f /dev/vda